Driveway Cost Calculator
Free, no signup. Material, labor, base, delivery and tax update as you type.
Example values are loaded (a 20 × 40 ft driveway, 3 in deep, $120 per ton, $5 per sq ft labor). Replace them with your own numbers.
Compare surfaces for this area
Installed cost ranges from published guides, multiplied by your area. See Sources below.
Check a contractor quote
Enter the total you were quoted to see its cost per sq ft for this area.
Estimate only. Without labor and site prep entered, the total covers materials and delivery. Always get quotes from 2–3 local contractors.
Cost benchmarks used by this calculator
Last updated: November 2026 · Tonnage uses 145 lb/ft³ hot mix asphalt · Sources
What This Driveway Cost Calculator Is For
What people use it for
- Budgeting before calling a paving contractor
- Checking whether a quote is fair
- Choosing between an overlay and a full replacement
- Comparing asphalt, concrete and gravel for the same size
- Estimating asphalt material for a lot or private road
Problems people run into
- Quotes that differ by thousands of dollars
- Not knowing if base work, tear-out or delivery is included
- Mixing up price per ton and price per square foot
- Not knowing how thick the asphalt should be
- Small jobs priced above the usual per-sq-ft rate
How this tool helps
- Splits the total into material, labor, base, removal, delivery and tax
- Shows cost per sq ft so quotes compare fairly
- Checks your total against published ranges
- Compares surfaces and checks a quote in one place
- Lets you replace every default with your local numbers
Asphalt, Concrete & Gravel Driveway Cost Per Square Foot
Installed prices per square foot from published cost guides. Ranges differ by source and market, so treat them as a starting point and check them against local quotes.
| Surface | Installed cost per sq ft | 800 sq ft (20 × 40) | Source |
|---|---|---|---|
| New asphalt | $7–$13 | $5,600–$10,400 | HomeAdvisor, Angi |
| Asphalt replacement (tear-out + new) | $8–$15 | $6,400–$12,000 | HomeAdvisor, Angi |
| Asphalt overlay | $3–$7 | $2,400–$5,600 | HomeAdvisor, Angi |
| Recycled asphalt | $6.20–$8.75 | $4,960–$7,000 | HomeAdvisor |
| Chip seal (tar and chip) | $1–$5 | $800–$4,000 | This Old House, citing Angi |
| Concrete | $8–$20 | $6,400–$16,000 | NerdWallet |
| Gravel (stone) | $1–$3 | $800–$2,400 | This Old House, citing Angi |
Some sources sit higher: Homewyse lists a May 2026 national average for an asphalt driveway starting at $12.46–$15.23 per sq ft. Some stone types cost more than $3 per sq ft.
Cost per ton vs cost per square foot
They measure different things. Price per ton is the mix only. Price per square foot is the finished driveway with labor, base and equipment. To convert material to square feet: price per ton × tons per sq ft, where tons per sq ft = thickness in inches × 0.00604.
Blacktop, tarmac, bitumen, liquid asphalt
Blacktop is another word for asphalt paving, and tarmac is the common UK word. Bitumen is the sticky binder inside the mix, sometimes called liquid asphalt, so a "liquid asphalt" price usually means the binder, not a finished driveway.
A "load" is a truck of mix. Truck sizes vary, so ask the plant for truck capacity, price per ton and any minimum-load fee.
Driveway Cost by Size
Tons are before waste. The installed range multiplies each area by $7–$13 per sq ft, the published range for a new asphalt driveway, which includes labor and basic prep. Your local rate may differ, so confirm it with contractors in your area.
| Driveway | Size | Area | Tons at 3 in | Tons at 4 in | Installed range |
|---|---|---|---|---|---|
| 1-car | 10 × 20 ft | 200 sq ft | 3.6 | 4.8 | $1,400–$2,600 |
| 2-car | 20 × 20 ft | 400 sq ft | 7.3 | 9.7 | $2,800–$5,200 |
| Long single | 12 × 50 ft | 600 sq ft | 10.9 | 14.5 | $4,200–$7,800 |
| Common 20x40 | 20 × 40 ft | 800 sq ft | 14.5 | 19.3 | $5,600–$10,400 |
| 1,000 sq ft | 20 × 50 ft | 1,000 sq ft | 18.1 | 24.2 | $7,000–$13,000 |
| 100 ft driveway | 12 × 100 ft | 1,200 sq ft | 21.8 | 29.0 | $8,400–$15,600 |
Per-square-foot rates often drop a little on bigger jobs, and very small jobs can cost more per sq ft. For asphalt tonnage alone, use the asphalt calculator.
What Affects Driveway Cost?
A full driveway paving project has several cost categories that vary by region and site conditions. Enter what you know in the calculator and leave the rest at zero.
Asphalt tonnage × price per ton. HomeAdvisor lists hot mix at about $100–$200 per ton. Plants and public bids can be lower, so get a local quote.
Delivery is often a flat fee per load plus any minimum-load charge. Ask the plant for truck size and fees.
HomeAdvisor puts installation labor at about $5–$7 per sq ft, roughly half of the total. Crew, grader and roller are included in that.
Excavation and grading can add $5–$10 per sq ft where needed, plus a compacted gravel base. Size the base with the gravel calculator.
Tear-out and hauling away is about $1–$2 per sq ft for asphalt. Choose "Replacement" in the calculator to include it.
Every extra inch adds about 0.006 tons per sq ft. Curved or custom shapes and steep slopes add labor and material.
Asphalt vs Concrete vs Gravel — Full Comparison
Asphalt usually costs less up front than concrete and is quicker to install. Gravel is the cheapest to build but needs regular regrading. Use the right calculator to price each option for your own dimensions.
| Type | Installed cost per sq ft | Typical life | Upkeep | Price it with |
|---|---|---|---|---|
| Asphalt | $7–$13 | 15–30 years | Sealcoat every few years and crack repair | Asphalt Calculator |
| Concrete | $8–$20 | 30–40 years | Little sealing, but cracks are harder to repair | Concrete Calculator |
| Gravel | $1–$3 | Varies | Regrading and topping up | Gravel Calculator |
| Asphalt millings | $6.20–$8.75 (recycled) | Varies | Needs rolling and occasional top-up | Asphalt Millings Calculator |
| Chip seal | $1–$5 | Varies | More texture, reseal as it wears | Not covered by tonnage |
you want a lower up-front cost, a quick install and easy repairs.
you want the longest life and can pay more up front, especially in hot climates.
budget matters most and you accept regular regrading.
Concrete figures from NerdWallet. Asphalt lifespan from HomeAdvisor. Gravel and chip seal from This Old House citing Angi. See Sources.
Driveway Cost by Region — 2026 US Averages
Reliable per-state averages are rare and often contradict each other, so we show national benchmarks from named publishers and let you test your own local numbers in the calculator.
| Source | What it reports |
|---|---|
| HomeAdvisor | Typical total $3,128–$7,391, average $5,258. About $7–$13 per sq ft for a new driveway. |
| NerdWallet | Typical total $5,258. About $7–$15 per sq ft including labor. |
| Homewyse (May 2026) | National average starts at $12.46–$15.23 per sq ft. |
Why your region can cost more or less
- Labor rates: cities and high cost-of-living areas usually charge more.
- Climate: freeze-thaw cycles, heavy rain or very hot summers can call for a thicker layer or base.
- Distance from the plant: longer hauls raise delivery charges, and hot mix cools in transit.
- Soil and drainage: poor soil means more excavation and base work.
Turn this into your local number
- Call a local asphalt plant for the delivered price per ton and enter it above.
- Take labor per sq ft from two or three written quotes and enter it as labor.
- Add base, grading or removal if your site needs them.
- Compare the total per sq ft with the published ranges shown in your results.
800 Sq Ft Two-Car Driveway Cost — Estimate for Your City
We do not list city-by-city prices we cannot verify. This table shows what an 800 sq ft (20 × 40 ft) driveway costs at published rates, so you can see where a quote from your city falls.
| Scenario | Rate per sq ft | 800 sq ft total |
|---|---|---|
| Overlay on a sound driveway | $3–$7 | $2,400–$5,600 |
| New asphalt (HomeAdvisor, Angi) | $7–$13 | $5,600–$10,400 |
| Replacement with tear-out | $8–$15 | $6,400–$12,000 |
| Homewyse national average (May 2026) | $12.46–$15.23 | $9,968–$12,184 |
Use the calculator above with your city's price per ton and labor rate for a closer figure.
Tips to Get Accurate Contractor Quotes
A fair comparison needs quotes that cover the same work. Use these steps, then run each total through the quote checker above.
Ask each contractor to price the same size and thickness.
Thickness, base depth, tons of asphalt, grading, removal and delivery should each be listed.
Divide each total by the same area so differently sized quotes compare fairly.
Base work, tear-out, drainage, edging and sealing are common extras.
Compare the contractor's tons with the asphalt calculator. A big gap means different thickness or scope.
Ask what is covered, for how long, and request proof of insurance.
How to Estimate Asphalt Driveway Cost
Work out the area, convert it to tons of asphalt, then multiply by your local price. Hot mix asphalt weighs about 145 lb per cubic foot once compacted, and the calculator uses that figure. For tonnage alone, the asphalt calculator gives the same result without costs.
Tons = Area × (Thickness in inches ÷ 12) × 145 ÷ 2,000 × (1 + waste %)
Material cost = Tons × Price per ton
Project estimate = Material + Labor + Site prep + Removal + Delivery + Tax
Area = 800 sq ft
Tons = 800 × (3 ÷ 12) × 145 ÷ 2,000 × 1.05 = 15.2 tons
Material = 15.2 × $120 = about $1,830
With $5 per sq ft labor ($4,000) the total is about $5,830, or $7.28 per sq ft.
Ways to Lower Your Driveway Paving Cost
Ask each contractor for the thickness, base prep and price per sq ft in writing, so quotes compare fairly.
An overlay over a solid existing base usually costs less than full removal and replacement.
Plan sealcoating after the new surface has cured, as your contractor recommends, to slow wear and cracking.
Driveway Cost Calculator — Common Questions
Most published guides put a new asphalt driveway at about $7–$13 per square foot installed, with replacement at $8–$15 and an overlay at $3–$7 (HomeAdvisor, Angi). HomeAdvisor's typical total is $3,128–$7,391, with an average of $5,258. A 20x40 ft (800 sq ft) driveway is roughly $5,600–$10,400 at the new-driveway rate. Your price depends on location, the condition of the existing base and contractor rates.
A new driveway is about $7–$13 per square foot including labor and materials. HomeAdvisor puts labor at about $5–$7 per square foot, roughly half the total. Replacement runs $8–$15 because tear-out is included, and an overlay is $3–$7. Homewyse's May 2026 national average starts higher, at $12.46–$15.23, so always compare with local quotes.
A 20x40 ft driveway is 800 sq ft. At $7–$13 per square foot installed that is about $5,600–$10,400, and an overlay at $3–$7 is about $2,400–$5,600. It needs about 14.5 tons of asphalt at 3 inches, so material is only part of the total, at around $1,830 at $120 per ton.
A 20x40 ft driveway is 800 sq ft. At 3 inches thick it needs about 14.5 tons of asphalt, and at 4 inches about 19.3 tons, before extra for waste. Use the asphalt calculator for other sizes.
A 100 ft driveway that is 12 ft wide is 1,200 sq ft. At $7–$13 per sq ft installed, that is roughly $8,400–$15,600. It needs about 21.8 tons at 3 inches thick.
HomeAdvisor lists hot mix asphalt at about $100–$200 per ton. Prices at the plant can be lower: a 2026 public bid in Kitsap County, Washington listed $80 per ton for 1/2-inch hot mix. Price depends on region, mix, delivery distance and order size, so call a local plant and enter the quote in the calculator. At 3 inches, one ton covers about 55 sq ft.
A load is one truck of mix, and truck sizes vary. Ask the plant for the truck capacity, the price per ton, and any minimum-load or short-load fee. The cost is tons × price per ton plus delivery, which the calculator works out for your size.
It estimates asphalt tonnage and material cost. You can also enter optional labor per square foot, a site prep amount and, for replacements, old driveway removal to get a fuller project estimate. Excavation and grading vary a lot, so use a contractor quote for those.
Most residential driveways use about 2–3 inches of compacted hot mix asphalt over a prepared 4–6 inch gravel base. Cold climates, hot climates that soften asphalt, heavy vehicles or weak soil often call for 3–4 inches or more. The calculator defaults to 3 inches for a new driveway and lets you pick 2, 3, 4 or 6.
If the base is firm and cracks are minor, an asphalt overlay can cost less than full replacement. If the surface has deep ruts, drainage problems or a failing base, replacement is usually the better long-term choice. A contractor can check the base before you decide.
You can use it for a rough material estimate by choosing Parking lot / road. Lots and roads usually need thicker asphalt, often 3–6 inches depending on traffic, over a deeper base, plus drainage and striping, so ask a commercial paving contractor for a proper bid.
Asphalt is usually cheaper than concrete: about $7–$13 per square foot for new asphalt versus about $8–$20 for concrete (NerdWallet). Gravel is cheapest at about $1–$3 per square foot for a stone driveway, but it needs regular regrading. Concrete often lasts longer, about 30–40 years versus 15–30 for asphalt. Price each one with the concrete calculator or gravel calculator.
A chip seal, also called tar and chip, typically costs about $1–$5 per square foot (Angi), or roughly $800–$4,000 for 800 sq ft. It gives a textured finish at a lower cost than hot mix, but it is a different method, so this calculator's asphalt tonnage does not apply to it.
Blacktop is another name for asphalt paving, and tarmac is the common UK word for it. Bitumen is the sticky binder inside the mix, sometimes called liquid asphalt. A liquid asphalt price usually means the binder, not a finished driveway, so it will not match a driveway cost per square foot.
Sources and How We Calculate
Tonnage = area × thickness × 145 lb/ft³ ÷ 2,000, plus waste. Total = material + labor + site prep + removal + delivery + tax. Cost ranges come from the guides below and differ between publishers, so use them to sense-check, not as a quote. Last reviewed November 2026.
- HomeAdvisor — asphalt driveway cost (per sq ft ranges, labor, removal, price per ton)
- Angi — cost to install an asphalt driveway
- NerdWallet — asphalt vs concrete driveway cost
- Homewyse — cost to install an asphaltic concrete driveway (May 2026)
- Hunker — concrete vs gravel vs asphalt driveway cost
- This Old House — driveway types and costs (chip seal, gravel; data from Angi)
- Kitsap County, WA — 2026 hot mix asphalt bid tabulation (public price-per-ton example)
Update log: Nov 2026 — rebuilt the calculator with project types, shapes, removal, quote checker and surface comparison; updated per-sq-ft ranges to published HomeAdvisor and Angi figures.
Other Calculators You May Need
Asphalt Calculator
Basic tonnage and volume calculation for any asphalt project.
Sealcoat Calculator
Estimate sealcoat gallons to protect your new driveway after installation.
Gravel Calculator
Calculate gravel base needed before laying asphalt.
Asphalt Millings
A low-cost alternative surface for unpaved driveways.
Concrete Calculator
Compare a concrete driveway slab by cubic yards and bags.